Download your Pal Owner Manual : Download v11.11
StompLight Pal Owner’s Manual v11.11
Congratulations on your purchase and commitment to your art and your audience! With proper care your StompLight Pal will last for years providing reliable performance lighting. Please register your Pal on our website.
You are going to need a bigger Tip Jar!
Never plug a microphone or any audio source into the DMX input/output jacks.
These jacks are for DMX connection only.
Do not use non-StompLight power adapters as they may damage your StompLight product.
Powering the Pal On
Plug in the included 12-volt 1.5 amp center-positive StompLight Power Adapter to a standard power source. The StompLight Pal is now powered on. StompLight products may also be powered with an optional StompLight Power Bank providing up to 7 hours of "unplugged" operation.
Brightness may be adjusted using the Brightness Adjustment Knob.
How to Load your Pal with a Solid Color and use as a stand-alone Stage Light.
One of the cool features of the StompLight Pal is that it can be connected to a StompLight Pal that is set to Solid Color Mode and then “loaded” with a selected solid color. Then the Pal and the Pro can be disconnected and the Pal can be repositioned and remain a solid color stage light. For ultimate portability and ease consider the use a StompLight Li Ion Power Adapter to power your Pal when utilizing this feature.
- Connect your Pro and Pal using a XLR cable
- Power up both units
- Select Solid Color Mode on the StompLight Pro Effect Pedal
- Turn on the Pro and turn both units to full brightness. Both the pro and Pal should show identical light.
- Carefully disconnect the XLR cable from the Pal
- Turn the brightness down on both units to a comfortable brightness.
- Being careful to not unpower the Pal you can now move it to a location to create stage lighting with adjustable brightness.
How to attach your StompLight Pal to a microphone stand.
The StompLight Pal comes with the holes and fasteners installed (3 screws in a triangular shape on bottom center) for the optional mounting to a microphone stand using the StompLight mic stand adapter (optional).
You can purchase the StompLight Mic Stand adapter on the StompLight website or at your local StompLight Authorized Dealer. This is a easy way to create side fill of a performance area or light a keyboardist, pedal steel player or a drummer. Please note: Use of any other screws or drilling into enclosure is a violation of warranty.
The StompLight Pal is mounted using the two pre-drilled locations using the included (3) Phillips head screws. The screws come mounted onto the base in a triangular form.
How to connect your StompLight Pal
- Stage your StompLight Pro and Pal(s).
- Power up the StompLight DMX Professional effect pedal.
- Locate the DMX out connector on the rear panel of StompLight DMX Pro. Using a XLR (mic) cable or DMX 3-pin cable, “daisy chain” your StompLight Pal(s) via the in/out DMX connectors on each unit. Mic cables will work if you do not have DMX 3-pin cables.
- Power up your StompLight Pals using the included StompLight power adapters or the rechargeable StompLight Li Ion Power Banks.
- Turn on the lighting on the StompLight Pro and scroll through the Modes. Whatever lighting you choose and whatever adjustments you make on the Pro will be replicated on each of the StompLight Pals.
- You may also adjust the Pal’s brightness with the Brightness Knob
StompLight Pal is not responding
StompLight Pal needs to be connected to a StompLight Pro Effect Pedal, StompLight Junior, or an active DMX lighting controller that is on and sending a signal to the Pal.
Cable may be improperly connected.
Unplug power adapter, wait 10 seconds and plug power adapter back in.
Try a different microphone cable or a 3-pin DMX cable. You may purchase these through the Stomplight website.
LED Array or Diffuser becomes loose
Carefully tighten the Array screws using a 1/16 Allen Wrench.
StompLight Pal is not Powering Up
Inspect Power Adapter. StompLight requires a center-positive 12 volt 1.5 amp power adapter. Typical effect pedal adapters will not work. If a replacement is needed contact StompLight.
When using the StompLight Power Bank be sure all cables are secure and Power Bank’s green indicator LEDS are lit.
Verify wall power is active
LED Array may be damaged
Here are some suggestions on staging your StompLight.
- Start by performing with lower amounts of light. Take caution in the angle and brightness. Take some video and pics. You'll be surprised how good you look at lower brightness.
- Purchase some rechargeable Li Ion StompLight Power Banks. They make set up/break down so easy!
- Understand the eye responds to colors in different ways. Blue will seem dimmer but not in the video or pics.
- If there are house lights in the performance area dim them if possible.
- The StompLight Professional and StompLight Pal work as extraordinary up-lights but may be positioned to side fill or also back light. StompLight products can be set on pedal boards, speaker cabinets, easily mounted to mic stands using the StompLight Surface-Mount Flange Mic Stand Adapter (Female), set on DJ decks, and keyboards. Explore and have fun. Send us your videos and pics! We love to see them.
- Solo & Duo Performers - Typical placement of a StompLight is on the floor off to the side. Duos can place a StompLight on the floor in between each performer or ideally add a StompLight Pal providing each artist to have lighting on each side. As always adjust the brightness so it is not over powering.
- Bandsand DJs– Suggested options:
- Best set up is each performer has a StompLight Professional Effect Pedal or StompLight Pal highlighting their artistic area.
- Take caution in the angle and brightness. Less is more.
- A couple StompLight Pros set as a side fill or placed in the front of a band/DJ will add exciting color with independent control.
- Place a StompLight DMX Professional highlighting the drum kit set to Microphone Mode and the drum sound and audio frequencies will create dynamic lighting effects.
- See the DJ/EDM Artist Animation on the StompLight website. Run a mono feed from your mixer into the 1/4" input. Add additional daisy chained StompLight Pals on the floor in front of your performance deck facing the audience.
DMX (Digital Multiplex) 101 and StompLight Products
DMX (Digital Multiplex) is a standard for digital communication networks that are commonly used to control stage lighting and effects. The StompLight DMX Professional lighting effect pedal is also a simple three channel DMX controller.
Channel 1 is the red channel Channel 2 is the green channel Channel 3 is the blue channel
The StompLight DMX Professional can control any DMX receiver than has a 3-channel mode. (Most RGB fixtures)
The channels in StompLight are fixed to 1, 2 and 3 so the DMX fixture you are using must be able to set its starting channel. (All that we have looked at can) StompLight connects to DMX fixtures using typical consumer three pin XLR. Cables with a nominal impedance of 110 Ohms are preferred. These XLR connectors are in parallel. Pin 1 is the shield, Pin 2 is Data Negative and pin 3 is Data Positive.
The StompLight DMX Professional defaults to Controller Mode when powered up meaning when connected to other DMX devices like the StompLight Pal it sends a signal to the other devices telling them what to do. Important to note that if you already have a DMX Controller and want your StompLight DMX Professional Effect Pedal to work as a Slave you must power up your StompLight Pro in Slave/DMX Client Mode. If you forget there will be a conflict. The StompLight Professional can be set to Slave/DMX Client Mode by holding down the MODE switch when powering up. (See User Configuration Chart) This should be done before connecting it to the DMX chain.
DMX fixtures receive their data through a serial Daisy Chain. The Data Out connector on the rear panel of the StompLight Pro connects to the Data In connector of any DMX fixture, whose Data Out connector goes to the Data In connector of the next fixture, etc. The last fixture in the chain should have a DMX terminator installed, particularly if the chain is over 20 feet long. One or two units with short cables will probably work fine without the DMX terminator.
The maximum number of DMX fixtures on a single chain is 32. The maximum length is about 1500 feet. Ideally data grade cables for DMX, not microphone cables when building a Daisy Chain longer than 60 feet. Microphone cables will work, but will degrade the DMX signal faster than data grades will.
- Cree LEDs with optical control, RGB color mixing at 350 lumens
- DMX512 compatible and capable of being a stand-alone stage light
- Designed in the form factor of a floor monitor with multiple lighting angles
- Light weight and robust
- Quickly mounts to a mic stand with a StompLight Mic Stand Adapter.
- Ultimate portability using our optional Rechargeable StompLight Power Brick for "off the grid" use
- Robust powder coated custom engineered aluminum enclosure
- Adjustable brightness with a vintage Daier “Moog Synth” control knob
- 3-pin DMX connectors for daisy chaining with StompLight products and other DMX products
- 12 volt 1.5 amp power requirement with included “center position” wall wort power adapter
- Length: 7.3” (18.4 cm) x Width 5.3” (13.5 cm) x Height 3.9” (10 cm)
- Weight: 1.7 pounds
- Engineered and Assembled in the USA
- 1 year warranty
- This product is covered by U.S. Patent Nos: 9,462,654; 9,185,776
- FCC, IC and CE compliant. This device complies with Part 15 of the FCC rules
Register your Product on the StompLight Website
All StompLight products come with a one year limited warranty on parts and workmanship from date of purchase (or delivery, in the case of pre-orders). The warranty remains valid only if you have registered your StompLight product on the StompLight website with the serial number on the unit not defaced or removed. Warranty does not cover damage due to misuse, unauthorized tampering, accident or neglect. During this period we will repair or replace (at our option) defective units free of charge. If you have a problem most issues can be resolved by visiting the Frequently Asked Questions and reviewing the Troubleshooting Chart.
If your issue cannot be resolved there, please email firstname.lastname@example.org with General Repair Ticket Request (see below) and we will help you.
General Repair Ticket Request requires the following information.
- Are you the original purchaser?
- Date purchased
- Where did you purchase your product?
- What is wrong with it?
If we can't get you back up and running with some techy mojo via email we may ask you to ship us your StompLight. We require a Return Merchandise Authorization before returning a StompLight product for repair. We only repair products that have been made by us. There will be repair fees for our products that have malfunctioned from user error like plugging in wrong power supply, running an audio signal into the DMX connectors or running over it with a truck, etc.
RMA-Return Merchandise Authorization/Shipping Details
Once we receive your Repair Ticket Email Request we may issue you a RMA -Return Merchandise Authorization. The customer then ships the unit to StompLight with the RMA number written prominently on the package. The customer pays the shipping to StompLight.
MJ Ahern / StompLight International, LLC
20 Portola Avenue - 365
El Granada, CA 94018 USA
If there is a real failure that is covered by the warranty we will fix or replace the unit, and send it back to the customer, shipping paid by StompLight International LLC. If there is a problem that is not covered by warranty, we will give you a repair estimate and the customer may approve the repair or choose not to. Customer pays for the repair and for the return shipping and handling
When return shipping charges and repair fee apply they will need to be collected prior to shipping the StompLight product back to the customer.
Refund and Exchange Policy
If you are not satisfied with your StompLight product, email us. We will work like crazy to make you a satisfied customer.
StompLight International, LLC, 20 Avenue Portola - 365, El Granada, CA 94018, 650.815.7997 info@stompLight.com